Eclipse 4100 Elliptical Trainer Manual

• 12223 Answers SOURCE: Detachthe ends of the pedals from the crank axles. Spread a layer of machine greaseover the crank axles, then reattach the ends of the pedals.2 Removethe bolts connecting the pedals to the swing arms. Detach the pedals from thearms, then spread a layer of machine grease over the axles on the swing arms.On some models, the bolts may also serve as the axles. Reattach the pedals tothe arms.3 Removethe bolts connecting the swing arms to the elliptical's upright. Detach theswing arms from the upright, then spread a layer of machine grease over theaxles on the upright. Reattach the arms to the upright. Posted on Nov 28, 2011.

• 12223 Answers SOURCE: Removethe bolts or screws securing the console to the upright assembly. Lift theconsole and confirm that the cable connections are secure. Remove the coverfrom the console's battery bay and install a fresh set of batteries. Replacethe battery cover.2 Detachthe ends of the pedals from the crank axles. Remove the left and right discshields and side shields.

Inspect the interior of the base unit and locate theflywheel.3 Inspectthe flywheel as it turns. Free Download Roblox Cheat Engine Hack Codes 2013 Programs Like Limewire. Locate the magnet installed on the flywheel. Turn theflywheel until the magnet passes in front of the nearby reed switch. Loosen thescrew securing the switch in place. Rotate the switch to reduce the gap betweenit and the magnet.

Tighten the screw.4 Replacethe left and right disc shields and side shields. Reattach the ends of thepedals to the crank axles. Good luck, sincerely.

Manual, Owners, SM 4100 - Product Image 4002194 Manual, Owners, SM 4100. SM 4100 Owners Manual. $19.64 / each. 6004219 HSNG,TCD,Plastic,Black G03562BC Used on WLEL45070 - WESLO ECLIPSE II ELLIPTICAL, WLEL45071 - WESLO ECLIPSE II ELLIPTICAL, WLEMEL45000 - WESLO ECLIPSE II.

Posted on Dec 03, 2011. • 12223 Answers SOURCE: Do this for your console Elliptical:Removethe bolts or screws securing the console to the upright assembly.

Lift theconsole and confirm that the cable connections are secure. Remove the coverfrom the console's battery bay and install a fresh set of batteries. Replacethe battery cover.2 Detachthe ends of the pedals from the crank axles. Remove the left and right discshields and side shields. Inspect the interior of the base unit and locate theflywheel.3 Inspectthe flywheel as it turns. Locate the magnet installed on the flywheel.

Turn theflywheel until the magnet passes in front of the nearby reed switch. Loosen thescrew securing the switch in place. Rotate the switch to reduce the gap betweenit and the magnet. Tighten the screw.4 Replace the left and right disc shields and sideshields.

Reattach the ends of the pedals to the crank axles Good luck, sincerely. G-d bless you. E.CUADRA MANAGUA, NICARAGUA. Posted on Dec 06, 2011. Nordic Track Nordictrack Cx1055 Elliptical Incline Motor For.

Cx1055_ elliptic/ resistance • Nordic Track Nordictrack Cx1055 Elliptical Incline Motor For Model Number 285090.the bolts that secure the magnet4=if there are slips, the resistance will. My schwinn 460 elliptical resistance cannot be changed When I increase the.

Every time I increase the resistance it will go to that level of resistance but within a. Www.shopyourway.com >Manage My Life >Questions • • Aug 10, 2013 - I bought a CX 1055 Nordick Track elliptical at a garage sale.

I noticed that the resistance doesn't really change between levels. 100 dollars, but how much would it cost to have someone come out and do the replacement for me? I wonder if maybe something shifted when I brought it to my apartment?Missing: slips [PDF] • NordicTrack4.

Place the elliptical exerciser on a level sur- face, with a mat beneath it to protect the. The CX 1055 elliptical exerciser is an. 1055 elliptical exerciser features adjustableresistance. Press the Odometer button again; the words 'My. Jan 05, 2016 . Follow this steps and fix it.

God bless you Check power problems if the console on the elliptical machine does not light up. Make sure that the plug for the machine is secure in the outlet. If it is plugged in, ensure that the outlet is receiving power. Check the breaker to make sure it has not tripped off. Be sure that you are using the correct adapter that came with the elliptical machine. Because different adapters are able to handle differing amounts of energy, the wrong adapter will not transfer electricity like it should.

If the adapter is pinched or damaged, this could also alter its effectiveness. • 2 Make sure the correct adapter is being used if the resistance settings seem to be too hard or too easy. If the correct adapter is being used, reset the machine. To reset the machine, either switch the 'On/Off' button or unplug the machine from the wall. Doing this will allow the device to reset itself to the default resistance. Turn on or plug the device back into the wall and retry all of the levels of resistance. • 3 Do not be concerned if you see small particles left on the guide rails.

Over time, the roller wheels gradually wear down. When this occurs, they leave residue on the rails. Because this is considered to be normal wear, all you need to do to fix the problem is wipe the rails off with a damp cloth. • 4 Minimize the risk of receiving erratic readouts on the monitors by avoiding outside interference.

For example, gripping the heart rate handlebars too tightly can affect the monitor. Similarly, the heart rate grips can be rendered less effective when there is too much vibration. Consider not holding these monitors throughout the workout to minimize vibration. The readouts also can be affected by jewelry. To minimize errors, take off rings and other jewelry before working out on an elliptical machine.

Oct 17, 2013 . Follow this steps and replace batteries too. God bless you Check power problems if the console on the elliptical machine does not light up. Make sure that the plug for the machine is secure in the outlet. If it is plugged in, ensure that the outlet is receiving power. Check the breaker to make sure it has not tripped off.

Be sure that you are using the correct adapter that came with the elliptical machine. Because different adapters are able to handle differing amounts of energy, the wrong adapter will not transfer electricity like it should. If the adapter is pinched or damaged, this could also alter its effectiveness. 2 Make sure the correct adapter is being used if the resistance settings seem to be too hard or too easy.

If the correct adapter is being used, reset the machine. To reset the machine, either switch the 'On/Off' button or unplug the machine from the wall.

Doing this will allow the device to reset itself to the default resistance. Turn on or plug the device back into the wall and retry all of the levels of resistanc Oct 01, 2013 . Replace batteries and proceed with this steps and fix it. God bless you Check power problems if the console on the elliptical machine does not light up. Make sure that the plug for the machine is secure in the outlet. If it is plugged in, ensure that the outlet is receiving power. Check the breaker to make sure it has not tripped off.

Be sure that you are using the correct adapter that came with the elliptical machine. Because different adapters are able to handle differing amounts of energy, the wrong adapter will not transfer electricity like it should. If the adapter is pinched or damaged, this could also alter its effectiveness. • 2 Make sure the correct adapter is being used if the resistance settings seem to be too hard or too easy.

If the correct adapter is being used, reset the machine. To reset the machine, either switch the 'On/Off' button or unplug the machine from the wall.

Doing this will allow the device to reset itself to the default resistance. Turn on or plug the device back into the wall and retry all of the levels of resistance.

Read more: Oct 01, 2013 . Follow this steps and replace batteries and clean the contacts batteries. God bless you • Check power problems if the console on the elliptical machine does not light up.

Make sure that the plug for the machine is secure in the outlet. If it is plugged in, ensure that the outlet is receiving power.

Check the breaker to make sure it has not tripped off. Be sure that you are using the correct adapter that came with the elliptical machine. Because different adapters are able to handle differing amounts of energy, the wrong adapter will not transfer electricity like it should.

If the adapter is pinched or damaged, this could also alter its effectiveness. • 2 Make sure the correct adapter is being used if the resistance settings seem to be too hard or too easy. If the correct adapter is being used, reset the machine.

To reset the machine, either switch the 'On/Off' button or unplug the machine from the wall. Doing this will allow the device to reset itself to the default resistance. Turn on or plug the device back into the wall and retry all of the levels of resistance. Oct 01, 2013 .

Follow this steps and fix it. God bless you • Check power problems if the console on the elliptical machine does not light up. Make sure that the plug for the machine is secure in the outlet. If it is plugged in, ensure that the outlet is receiving power.

Check the breaker to make sure it has not tripped off. Be sure that you are using the correct adapter that came with the elliptical machine.

Because different adapters are able to handle differing amounts of energy, the wrong adapter will not transfer electricity like it should. If the adapter is pinched or damaged, this could also alter its effectiveness. • 2 Make sure the correct adapter is being used if the resistance settings seem to be too hard or too easy. If the correct adapter is being used, reset the machine. To reset the machine, either switch the 'On/Off' button or unplug the machine from the wall.

Doing this will allow the device to reset itself to the default resistance. Turn on or plug the device back into the wall and retry all of the levels of resistance.

Sep 30, 2013 . Be aware that the resistance is often the part that requires repair.

Resistance is managed magnetically, so often if the machine is working, but the resistance isn't setting correctly or at all, check the bolts that secure the magnets. If they are loose, the resistance will slip. If the bolts are fine, check the magnets themselves by using a refrigerator magnet and see if it is attracted or repelled by the your fridge magnet. If not, the magnets have de-magnetized and need to be replaced. God bless you May 22, 2013 . See the steps and fix it. God bless you Adjust the magnet with bolt attached there are loose, tight very well and ready the resistance is the main parts that need repair, However if the resistance is faulty, you must test again the magnet from the refrigerator by attracting or repeled, if do not pass this test replace it buying small cheaping from home depot or similar.

GoD BLess you • 1 Check your owner's manual for diagrams and definitions. You'll need this information when you put the elliptical back together.

You'll also want definitions in case you need to call the customer support line for assistance. • 2 Be aware that the resistance is often the part that requires repair. Dvd Rw Driver Windows Xp. Resistance is managed magnetically, so often if the machine is working, but the resistance isn't setting correctly or at all, check the bolts that secure the magnets. If they are loose, the resistance will slip. If the bolts are fine, check the magnets themselves by using a refrigerator magnet and see if it is attracted or repelled by the your fridge magnet. If not, the magnets have de-magnetized and need to be replaced.

• • For diagnostic help, to repair or find a new part, contact us! • 3 Consider that if the foot pedals are attached with bolts, any slipping can be fixed with a quick use of the wrench. But if the foot pedals are damaged or breaking, order new foot pedals (see Resources below) rather than run the risk of a pedal breaking while you're on the machine.

• 4 Check the hand bars. While not all people use them, as they can elevate your heart rate by up to 20 percent, they can become worn, too. While loose hand bars typically need a simple tightening of the bolt, be sure not to overtighten as the bolts can break. • 5 Know that if the axis is bent, it's likely you need a new machine. The axis is the central alignment of the elliptical. If the machine was used by a person who is over the maximum weight limit, it can be bent or damaged.

It's not an easy fix and a better idea is to upgrade to a sturdier machine. Read more: • 1 Check your owner's manual for diagrams and definitions. You'll need this information when you put the elliptical back together. You'll also want definitions in case you need to call the customer support line for assistance. • 2 Be aware that the resistance is often the part that requires repair.

Resistance is managed magnetically, so often if the machine is working, but the resistance isn't setting correctly or at all, check the bolts that secure the magnets. If they are loose, the resistance will slip. If the bolts are fine, check the magnets themselves by using a refrigerator magnet and see if it is attracted or repelled by the your fridge magnet. If not, the magnets have de-magnetized and need to be replaced.

• • For diagnostic help, to repair or find a new part, contact us! • 3 Consider that if the foot pedals are attached with bolts, any slipping can be fixed with a quick use of the wrench. But if the foot pedals are damaged or breaking, order new foot pedals (see Resources below) rather than run the risk of a pedal breaking while you're on the machine. • 4 Check the hand bars. While not all people use them, as they can elevate your heart rate by up to 20 percent, they can become worn, too. While loose hand bars typically need a simple tightening of the bolt, be sure not to overtighten as the bolts can break.

• 5 Know that if the axis is bent, it's likely you need a new machine. The axis is the central alignment of the elliptical.

If the machine was used by a person who is over the maximum weight limit, it can be bent or damaged. It's not an easy fix and a better idea is to upgrade to a sturdier machine. Read more: Nov 25, 2012 . Fitness Quest Eclipse 1175e Elliptical Trainers were recalled on December 11, 2007 for a fall hazard. During exercise, the foot pedal crank can break.

After receiving 190 reports of the crank breaking, the company is offering a replacement product or credit toward other Fitness Quest products. If the pedal falls off, be sure to save it; you will need the right foot platform to claim the replacement or credit. Owners should stop using the elliptical trainer immediately. Owners can receive a replacement with another Fitness Quest product or credit. (PDF) Questions? Contact at: (800) 321-9236 between 8:30 a.m.

ET, Monday through Friday. Or, e-mail productrecall@fitnessquest.com.

The Fitness Quest Eclipse 1175e Elliptical Trainer was sold at major sporting goods chains, such as Sports Authority, Modell's, Dunhams, and JC Penney stores in the United States from September 2006 to October 2007. Sale prices were $290 and $450. E1 errors are usually lubrication/resistance issues. Has the unit been oiled/greased recently?

Jan 10, 2009 .